Electronics For Imaging Fiery X12 Servisní příručka Strana 52
- Strana / 170
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
3
3-14 Performing Setup from the Control Panel
TCP/IP Setup options
When you set an IP address, subnet mask, or gateway address for the Fiery during
Setup, you can allow the Fiery to get these addresses automatically from a DHCP,
BOOTP, or RARP server. First, turn on or reboot the Fiery and allow it to reach Idle.
Next, make sure the DHCP, BOOTP, or RARP server is running. Finally, perform
Fiery Setup.
To configure the Fiery for TCP/IP, choose TCP/IP Setup.
Choose Ethernet Setup and enter the appropriate settings. Choose each network
type you use (Ethernet, Token Ring, or parallel port) and enter the appropriate
settings. Token Ring Setup appears as an option only if you have enabled Token
Ring in Port Setup.
NOTE: If TCP/IP is running on both an Ethernet and a Token Ring network, it is
assumed that the two networks are already routed to each other. The Fiery does not
function as a router.
Exit Protocol Setup
AppleTalk Setup
TCP/IP Setup
IPX/SPX Setup
Protocol Setup
Exit TCP/IP Setup
Ethernet Setup
Token Ring Setup
Parallel Port Setup
TCP/IP Setup
- Fiery X12/XP12 1
- Contents 7
- Introduction 11
- About this manual 11
- About the documentation 12
- Fiery on the network 15
- Chapter 1: 15
- Connecting to 15
- 1-3 Fiery on the network 17
- SERVER CONFIGURATION 17
- CONNECTION 17
- CLIENT SETUP 17
- FIERY SETUP 17
- Quick path to installation 18
- 2 Fiery Setup Chapter 3 19
- Key to setup: 24
- Back view of the Fiery X12 25
- Back view of the Fiery XP12 26
- Ethernet connection 27
- Token Ring connection 27
- Levels of access and control 29
- Chapter 2: 29
- Preparing for 29
- Fiery Setup 29
- 2-2 Preparing for Fiery Setup 30
- Passwords 31
- Fiery WebTools 32
- Control level scenarios 34
- Fiery system software 36
- About Setup 36
- Local Setup from the Fiery 37
- About Fiery Setup 39
- Chapter 3: 39
- Accessing Setup options 41
- Types of Setup screens 43
- Server Setup options 45
- Network Setup options 47
- Port Setup options 49
- Network Setup 50
- Port Setup 50
- Protocol Setup options 51
- Exit TCP/IP Setup 52
- Ethernet Setup 52
- Token Ring Setup 52
- Parallel Port Setup 52
- TCP/IP Setup 52
- Exit Protocol Setup 57
- AppleTalk Setup 57
- IPX/SPX Setup 57
- Protocol Setup 57
- Service Setup options 59
- Yes/No [No] 60
- Enable NDS 60
- Enable PServer 60
- ..” to go up one level 61
- ..” to go up the 62
- “..” to go up one level 63
- Remove support for 68
- File server name 68
- Service Setup 69
- PServer Setup 69
- PostScript Setup options 74
- PCL Setup options 76
- O ACCESS PCL SETUP OPTIONS: 77
- Color Setup options 78
- Presentation 79
- Relative 79
- Colorimetric 79
- Job Log Setup 82
- Change Password 83
- Font Archiving 84
- 84
- Clearing the Fiery 85
- O RESTORE THE FIERY: 86
- 2. Choose Print Pages 87
- 3. Select Configuration 87
- 4-1 Accessing Setup 89
- Local Fiery Setup 90
- Remote Fiery Setup 91
- General Setup options 92
- O SET OR CHANGE A PASSWORD: 94
- O REMOVE A PASSWORD: 94
- Protocols 99
- AppleTalk 101
- 4-15 General Setup options 103
- Services 104
- 4-17 General Setup options 105
- 4-19 General Setup options 107
- 4-21 General Setup options 109
- 6. Click OK 109
- Bindery Setup 110
- TO ADD BINDERY CONNECTIONS: 111
- O REMOVE BINDERY CONNECTIONS: 113
- Poll Interval 114
- 4-27 General Setup options 115
- 4-29 General Setup options 117
- Printer Setup options 119
- PS (PostScript) Setup 120
- PCL Setup 122
- Color Setup 124
- Exiting Setup 125
- 2. Click Configuration 126
- 3. Click Print 126
- Support for Fiery utilities 127
- Chapter 5: 127
- Setting up 127
- Network Servers 127
- Tips for experts—IPX networks 129
- Configuring an NDS connection 131
- FS = file server 131
- PS = print server 131
- is published 138
- O ACCESS THE FIERY WEBTOOLS: 139
- O PRINT TO THE FIERY: 142
- Managing print jobs 143
- Administrator functions 145
- Chapter 6: 145
- Administering 145
- Troubleshooting the Fiery 148
- Novell error messages 152
- Runtime error messages 153
- Fiery Token Ring option 157
- Appendix A: 157
- Token Ring 157
- Network Option 157
- A-2 Token Ring Network Option 158
- A-3 Token Ring Network Option 159
- 1. Turn off the Fiery 159
- IPX/SPX installations 160
- TCP/IP installations 160
- Numerics 161
Související produkty a manuály pro Servery Electronics For Imaging Fiery X12
(257 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce